Press and hold any button on your remote within 20 seconds. Hold the button until the locks cycle and it will be successfully programmed. Do the same thing to reset any additional remotes or remove the key from the ignition to end the programming mode.

Insert your key in the ignition on your Grand Prix and turn the key one click to the left to the “Accessory” option within the ignition options. Wait for your car to signal the programming sequence with a short beep, and turn the key back to the right one click, and then back to the left quickly.

2002 Pontiac Grand Prix Remote Programming

1. Remove key from ignition.
2. Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step.
3. Close all doors.
4. Turn ignition switch to ACC.
5. Within 1 second turn the ignition to OFF then back to ACC. (
6. Open then close the driver’s door.

While there are a few different reasons that a keyless entry remote might stop working, most of them are pretty easy to check yourself. The most common problem with these car key fobs is that the batteries just go dead over time, in which case replacing the battery should fix the problem.

NOTE: Because each of these steps represents a possible solution, check the function of the remote control after completing each step.

1. Make sure none of the remote buttons are jammed.
2. Reset the remote.
3. Clean the remote control terminals.
4. Replace with fresh batteries.
5. Perform a power reset on the TV.

How to Connect a Remote to a TV

1. Hold down the program button on the remote control for 3 seconds.
2. Press the “TV” button on the remote control to let the remote know it will be syncing with a TV.
3. Find the proper codes for the TV you are programing.

Hold down the Power button along with the button for the item for which you want to program your remote. Release both buttons when prompted. When your remote control’s LED light turns on and stays on, you can release the item’s button and the Power button. Point your remote at the item for which you want to program it.

Find the code Go to Settings . Scroll to Link with TV code. A blue TV code will show on your TV.

1. Press and hold down the SETUP button until the remote’s red light turns on.
2. Press and release the chosen device button (e.g., TV, CBL, DVD, AUD).
3. Enter the first 4-digit code for your device. The red light will turn off.
4. Point the remote at the device and test the buttons.

How to Find a Code for My Remote Control

1. Look through the User’s Manual for your remote control to find the code section.
2. Go to an website listing code, such as the Remote Code List (See References).
3. Call the manufacture of your remote and ask whether it can tell you the codes you need.

How to Program a Universal Remote using Universal Remote Codes

1. Enter device into setup mode.
2. Select the device type as TV.
3. key the universal remote code coresponding to your device from below list.
4. Verifying the results.
5. Setting up other device.

The codes are the universal defaults for that particular TV, DVR, DVD or VCR. Whether your universal remote control is made by GE, Sony, RCA or Philips, the codes will work if programmed correctly.

One-For-All Universal Remote Codes

• APEX – 0214 0216 0215 0401.
• GOLDSTAR – 0004 0009 0005 0227 0338 0012 0057 0080 0156.
• LG – 0004 0050 0009 0005 0227 0338 0012 0057 0080 0156.
• PANASONIC – 0171 0148 0054 0170 0062 0374 0381 0437 0950 0003 0070.
• SONY – 0128 0013 0002 0071 0380.

Other Brand Setting: Point the remote control at the TV, press and hold the button of corresponding brand for 5 seconds that needed to be set, hold the button until the TV tums off, and the setting is complete….

1. Go to your orders and start the return.
2. Select the return method.
3. Ship it!

A: You can use your universal remote with almost anything connected to your TV. You can control your Blu-ray, DVD, VCR,DVR, cable box, satellite, digital converter box, streaming devices and more.

Manually turn on the component you wish to program the remote to operate. Find the four-digit code for your brand of TV, VCR, DVD, satellite receiver, cable box, or digital TV converter in the enclosed code lists. Press and hold the CODE SEARCH key until the indicator light turns on. Release the CODE SEARCH key.

Hooking Up a Digital Converter Box:

1. Unplug Your TV. Turn off your television and unplug your TV before you begin.
2. Connect Your Antenna.
3. Choose Your Connector Type.
4. Connect the Box to the TV.
5. Plug In Your TV and Converter Box.
6. Tune Your TV to the Right Channel or Input.
7. Search for Channels.